How to change primer bulb on featherlite weedeater

By Netilar | 23.04.2021

how to change primer bulb on featherlite weedeater

The Primer Bulb Is Stuck in My Craftsman 32cc Weedwacker

Jun 05,  · Replacing the primer bulb on a Weed Eater Featherlite trimmer. The bulb split open over time. This is a straightforward fix that doesn’t take too much time t. Nov 03,  · I found lots of great videos on replacing a primer bulb, but none for the specific model shown here. The primer is mounted on a shaft that goes through the.

Table Of Contents. Quick Links. Table of Contents. Please do not return unit to retailer. Por favor, no devuelva el aparato al lugar de compra. Read and follow all Safety Rules and Operating Instructions before.

Failure to do vulb can result in serious injury. Lea el manual de instrucciones y siga todas las advertencias e. El no hacerlo puede resultar en lesiones. Lire le manuel d'instructions et bien respecter tous les avertisse. Previous Page. Next Page. Page 2 Keep others away when making carburetor adjustments. Use only recommended Weed Eater" ac- cessories and replacement parts. Have all maintenance and service not ex- wfedeater in this manual performed by an chage rized service dealer.

Remove objects rocks, broken glass, nails, wire, xhange. Hard objects can damage the trimmer head and be thrown causing serious injury. Use only for trimming, scalping, mowing and sweeping. Page 4 2-cycle air-cooled engine oil designed to be mixed at a ratio of Mix gasoline and how long is the movie atonement at a ratio of A ratio is obtained weedeaetr mixing 3.

Avoid any con- tact with the muffler. A hot muffler can cause weedeayer burns. Page 6 To stop engine: S Release the throttle trigger. Keep the line parallel to and above the surfaces being swept and move the tool from side to side. Remove spool by firmly pulling on tap button.

Clean entire surface of hub and spool. Engine flooded. Fuel tank empty. Spark plug not firing. This manual is also suitable for: Featherlite 25 ho sst. Print page 1 Print document 12 pages.

Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.

Article Breakdown

Apr 24,  · In this easy to follow video I show you how to replace the primer bulb on your Weedeater XT grass trimmer. The same procedure will apply to many models o. Folluw from the bulb to the carborator and you will see the spring with the shaft inside of it. Now look on the right side of the filter and you will see a screw head where the end of the shaft is - remove the screw, disconnect the fuel lines (they will more than likely be stuck so you will need to gently grab the hose over the nipple and gently twist the hose to loosen it) then remove the hoses, pull the part out. Folluw from the bulb to the carborator and you will see the spring with the shaft inside of it. Now look on the right side of the filter and you will see a screw head where the end of the shaft is - remove the screw, disconnect the fuel lines (they will more than likely be stuck so you will need to gently grab the hose over the nipple and gently twist the hose to loosen it) then remove the hoses, pull the part out.

The McCulloch trimmer is part of the line of trimmers designed to help homeowners control grass and weeds in hard to reach areas of the lawn and landscape. The 28cc gasoline-powered engine on the trimmer features a primer bulb that is used to transfer fuel from the tank into the carburetor to help during cold starting. The primer bulb is pressed several times each time the trimmer is started, resulting in wear over time.

Installing a new primer bulb on the McCulloch trimmer will help prevent down time. Place the McCulloch trimmer on a stable work surface such as a workbench or on a work shop floor. Pull the spark plug wire from the tip of the spark plug for safety while working. Remove the screw from the air filter housing cover with a screwdriver and pull the cover off the air filter housing. Remove the air filter from the housing.

Place a small container under the carburetor to catch any gas that might be in the primer fuel line. Grip the sides of the primer bulb bracket, located on the side of the air filter housing, and press in to release the tabs. Pull the bracket and bulb and bracket assembly out from the air filter housing. Pull the primer fuel line from the outlet on the back of the primer bulb assembly.

Obtain a replacement primer bulb assembly from a small engine repair shop. Connect the primer fuel line to the outlet on the back of the primer fuel assembly.

Snap the primer assembly back onto the side of the air filter housing. Push the assembly firmly in place until the tabs seat properly in the housing. Replace the air filter in the air filter housing, and then attach the housing cover on the housing and secure in place with the screw.

Keith Dooley has done work in the field of landscaping and design for more than 10 years. He has implemented his own designs, as well as pulled from techniques learned through studies, creating many landscapes for others to enjoy.

He has also maintained lawns, athletic fields, town parks, large gardens and game fields. By Keith Dooley. Related Articles.

2 thoughts on “How to change primer bulb on featherlite weedeater

Add a comment

Your email will not be published. Required fields are marked *