Removing Moldings from a Single Wall
Jan 31, †Ј To remove crown molding from your walls, just follow these simple steps. While time consuming, itТs fairly easy. Save Your Wall. The first step is to ensure your wall doesnТt get damaged in the process of removing the molding. Use a utility knife to cut the paint thatТs long-since dried between the molding and wall. How to Remove Crown Molding Step 1. Cut the caulking across the top and bottom edge of your crown molding. The edges of your crown molding were Step 2. Place the blade of your utility knife at the point where your crown molding meets your wall. Run or pull your Step 3. Begin your removal at.
Last Updated: February 21, References. This article was co-authored by our trained team of editors and researchers who validated ftom for accuracy and comprehensiveness.
There are 10 references how to picture in picture imovie in this article, which can be found at the bottom of the page. This article has been ermove 9, times. Learn more Crown molding is basically the equivalent of baseboard molding but is located where the wall meets the ceiling rather than where it meets the floor.
If you want to remove crown molding for any reason, do so by prying it off gently using a hammer and a pry bar.
If you plan to reinstall or reuse the molding elsewhere, remove the nails by pulling them through the backside to avoid damaging the face of the molding.
Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article methods. Things You'll Need. Related Articles.
Method 1 what is one ton in pounds All rights reserved. This image may not be used by other entities without the express written consent of wikiHow, Inc. Place a drop sheet on the floor underneath the crown molding. Lay down a canvas drop cloth, tarp, or plastic sheet on the floor underneath where you will be removing the molding to protect the floor.
This will catch any debris and make it easier what do dolphins eat and drink clean up after. If you don't have any kind of drop sheet, you could lay down some newspapers or pieces of cardboard as an alternative. Put on protective eyewear and work gloves. Wear a pair of safety glasses or eall to protect your eyes from any falling debris as you remove the molding.
Wear a pair of work gloves to protect your hands from scrapes and other accidents. Score the edges of the molding with fdom utility knife.
Use the tip of a sharp utility knife to carefully slice along the entire what is really going on between israel and palestine and bottom edges of the crown molding where it meets the wall and the ceiling.
This will cut through any paint and caulking that is filling the cracks between the crown molding and the wall and ceiling. A box cutter wal, as an alternative to a fro, knife. Tip : You can use this same method to remove baseboard molding along the bottom of a wall.
Cut any joints where pieces crlwn crown molding meet yow a utility knife. Use the tip of your utility knife to slice along the seams where pieces of crown molding meet in the corners and anywhere else where 2 pieces have a seam. This will cut through any caulking or paint at the seams so you can remove each piece of molding separately from the others that it touches.
Hammer a pry bar underneath the bottom edge of crwon molding at 1 corner. Stick the thin edge of the pry bar against the crease where the bottom of frm molding meets the wall in a corner. Carefully tap the pry bar into the crack by hitting the back flat end of it with a hammer. If you don't have a pry bar, you can hammer another utensil like a putty knife under the edge of the molding to make a small gap, then use the backside of a claw hammer to pry the molding away. Use the pry bar like a lever to separate the crown molding from the wall.
Start prying the crown molding off the wall using a lever motion with the pry bar. Only pry it as far rrmove it will easily come off so you avoid damaging the wall. If you want to add extra protection for the wall, slip a scrap piece of wood or a rag awll the back of the pry bar and the wall. Work your way down the section of crown molding using the same technique. Move the pry bar down the section of crown molding to wherever it is still stuck to the wall and hammer it underneath the bottom edge using your hammer.
Keep using the pry bar like a lever to pry the molding away from the wall. Use your hands to pull the molding off the wall once you have loosened it all. Use both hands to mooding pull the section of crown molding off the wall after you have pried it up as far as it will go along the reemove length of it.
Method 2 of Lay a section of molding face-down on a flat surface. Place the section remkve crown molding that you want to moldinf face-down so the back side with the nails is exposed. This will allow you to pull the nails out without damaging the front of the molding. Moldinv a pair of end cutting pliers to pull the nails through the back of the molding. Grab a nail tightly between the pincers ffrom the end cutting pliers. Roll the pliers forward, away from you, while simultaneously pulling to pull the nail through and out.
Scrape off excess paint or caulking with a thin putty knife or utility knife. Use the flat edge of a thin putty knife or the blade of a utility knife to carefully scrape away any pieces of paint or caulking that are stuck to the back or the edges of the molding. You will also be able to see if there is any damage to the molding after you scrape away the excess paint and caulking. Fill any splits or cracks with a dab of wood glue and clamp the molding to dry.
Squeeze a small bead of wood glue into any cracks or splits and wipe away the excess with a rag. Clamp the crown molding where it is damaged with a rubber clamp to hold the pieces together while the glue dries. Aim for 1 clamp every 10Ч12 in 25Ч30 cm or so. Include your email address to get a message when this question is answered. Submit a Tip All tip submissions are carefully reviewed before being published. Related wikiHows How to. How to. More References 1. About This Article. How to remove crown molding from wall by:.
Between a Rock and a Hard Place
Tired of the crown molding in your house? Want it removed temporarily to paint? Either way, the process is much the same. Although, if you plan to remove it permanently, you may not need to be quite as careful as if you plan to put it back later. To remove crown molding from your walls, just follow these simple steps.
The next step is going to involve a firm, metal putty knife. These tools are thin enough to get into tight spaces while still strong enough to act as weak crowbars. Begin at one end of a piece of molding. Place the corner of your putty knife against the seam between molding and wall and attempt to shove it in between the two.
If you have difficulty, try tapping the handle of the putty knife with a hammer. The extra force may be all it needs to separate the two. As a matter of fact, you can quickly replace your putty knife with an actual crowbar, which will more quickly pull the molding away.
Although, it is also more likely to split the molding into small pieces, which is why you should only take this speedy route if you intend to throw the molding away. Gently pry all the way down the molding, making an even amount of progress before returning to the beginning. As you get more space between your molding and the wall, you can switch to a straight-edged crowbar. Just remember, you still need to be careful to avoid splitting the wood of the molding. Finally, the molding should be removed.
Repeat this process on any remaining walls where you want to remove crown molding. We do this kind of thing all the time, and are happy to do it for you as well. Blog General Contracting. Between a Rock and a Hard Place The next step is going to involve a firm, metal putty knife. The Best Places for Mosaic Tile. Why Hire a General Contractor?