How to replace outside light fixture

By Kazijind | 11.06.2021

how to replace outside light fixture

How to Replace an Outdoor Light

Mar 27, In the video we kill AC power to the light fixture - remove the screws holding the old light fixture - cut the caulking around the base of the light - remo Author: backyardmech. Dec 20, A new light fixture should come with mounting hardware. Replace the old hardware with the new mounting bracket. Its important to use the bracket that came with the new light fixture, as things like screw sizes and hole orientation vary with different manufacturers and models. Use a level to make sure the crossbar is level.

Switching up your outdoor light fixtures is an easy way to revamp the look of a front porch or patio. Having adequate outdoor lighting on your home is not only attractive but also a safety precaution. Read on for simple instructions for installing outdoor lighting. Replacing exterior lights on your porch, patio, or garage is a quick and easy weekend project that will add major curb appeal to your home.

While outdoor lighting installation isn't complicated, there are some safety tips to know before you begin. Although exterior lights vary based on the type and manufacturer, there are a few key factors that are consistent with most.

Outdoor lights typically have three wires: black or red hotwhite or gray neutraland ground usually green or bare copper. Make sure to connect black to black, white to white, and ground to ground. Seal the top and sides of the fixture, so that if any water gets inside, it can drain out through the bottom.

Check to make sure that the junction box is in the wall far enough, the wires are tucked in, and all screws are properly secured.

The most important thing to remember when working on any project using electricity is to turn off the power from the main circuit breaker. Simply turning the light off is not the same thing, as there is still electricity flowing to that circuit. Before you begin any project dealing with electricity, you MUST disconnect the power at your main circuit breaker panel or fuse box. Do not reconnect until your project is finished. Make sure your work area is dry before beginning.

The saturdays lyrics what about us the existing light from the wall. The screws may be located underneath a mounting plate, which can be lifted off. Hold the light fixture in place while removing the screws with a screwdriver or power drill. Gangnam style what it means in english the old light fixture off from the wall.

While holding the light fixture, untwist the plastic wire connectors and wire ends to disconnect. A new light fixture should come with mounting hardware. Replace the old hardware with the new mounting bracket. Use a level to make sure the crossbar is level. Leave the ground bolt loose. This bolt is usually colored green. Wrap the ground wire once or twice around the threading of the ground bolt near the head, then tighten the ground bolt to secure.

Connect black to black, white to white, and ground to ground by twisting the bare ends of the wires together clockwise. The ground wire is typically green, but could also be a bare copper wire coming from the junction box. If the wire ends are not long enough to twist together you need about an inch of exposed wireuse wire snips to trim some of the plastic casing away from the wire. Use plastic wire connectors or electrical tape to seal the ends of the wires.

Give them a gentle tug to make sure the wires do not come apart. You may also want to wrap a couple of inches of electrical tape around the base of the connector where the wires meet for added waterproofing.

Carefully tuck all wires back into the junction box, making sure none are poking out. Attach the new light fixture to the mounting bracket using the provided hardware. Thread any lockup knobs onto the appropriate screws, and tighten to secure. Use a clear how to calculate morgage interest caulk and a caulk gun to seal the top and sides, if desired.

Insert a light bulb, if necessary, and turn the power back on from the main circuit breaker. How to Replace an Outdoor Light. By Lucy Wendel December 20, Save Pin FB ellipsis More. Power drill or screwdriver Outdoor light fixture with mounting hardware we used the Harbor Bay exterior light from Kichler Level Wire snips, if necessary Wire connectors Electrical tape Caulk gun, optional Clear silicone-based caulk, optional Light bulb, if not provided with light fixture.

Disconnecting wires from existing hardware. Installing new crossbar mounting bracket. Mounting new light fixture with screws. By Lucy Wendel. Comments Add Comment. Share options. Back to story Comment on this project Rate Review Comment on this story.

Tell us what you think Thanks for adding your feedback. Close Login. All rights reserved. View image.

Profile Menu

Jun 03, Here is a quick video on how to easily replace Front Porch Outside Lights. This video, your new lights & a little safety is all you usloveescort.com Dec 20, Hold the light fixture in place while removing the screws with a screwdriver or power drill. Lift the old light fixture off from the wall. While holding the light fixture, untwist the plastic wire connectors and wire ends to disconnect. Step 2: Replace the Mounting Bracket. Jun 03, Here is a quick video on how to easily replace Front Porch Outside Lights. This video, your new lights & a little safety is all you usloveescort.com

My garage light fixtures never really did a great job at putting off much useful light, and then they began to rust. Ideally, turn the power off at the breaker box. Unwrap your new light fixture; if it needs assembly do so per the instructions. This light needed the finial and optional arm installed. Check and see if your fixture comes with any special mounting hardware.

A lot of fixtures use universal mounting bars, so sometimes you can use what your previous fixture used. This fixture has its own hardware with a specific bolt spacing to mount it. Take care not to break off any of the little wires when trimming. Next remove the old fixture. Typically the fixtures will be mounted by a couple of small bolts with acorn nuts. Pull the fixture away from the wall mounting surface. The only thing that is guaranteed behind the fixture is wires, the rest, well, you never know!!!

Usually you will see an outlet box that the hardware is attached too. Do this for each wire. If your power is not off, the black will shock you. The white wire is neutral, and the bare copper or sometimes green wire is ground. Sometimes the ground wire will be connected with a wire nut to another ground wire, other times it will be connected to a ground screw on the hardware.

Replace wire nuts as you go. If needed, change the mounting hardware to the hardware that came with the fixture. Level the hardware as needed and tighten down all of the screws.

If your hardware has adjustable mounting bolts, dry fit the fixture to make sure they are at the correct length. This next part is much easier if there is a helper available. Have the helper hold fixture close enough that outlet wires and the fixture wires can be mated.

One color at a time, twist the fixture wire to the corresponding color outlet wire and replace the wire nut. Twist the wire nut righty tighty onto the wires until it is snug. Slightly tug on each wire to make sure they are secure in the wire nut. Repeat for each color.

Tuck the wire bundles into the outlet box. Place the light fixture onto the mounting bolts, and tighten down. Turn the power on and test the lights. Pick a caulk that is similar in color as your house. Yay, they work! Great instruction thanks. I am replaceing mine this weekend. But I find a utility knife is pretty useful to remove old silicone. Your email address will not be published. Notify me of follow-up comments by email. This site uses Akismet to reduce spam.

Learn how your comment data is processed. Comments Great instruction thanks. Leave a Reply Cancel reply Your email address will not be published. Copyright Thank you for wanting to share my work! No need for my permission to pin my work or to feature 1 or 2 pictures with full watermarks intact that link back to the original project.

Please do NOT copy tutorials. This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish.

Accept Read More. Necessary Always Enabled.

0 thoughts on “How to replace outside light fixture

Add a comment

Your email will not be published. Required fields are marked *